Looking for partners

Search
Close this search box.

F.A.Q.

Q: Are lithium iron phosphate batteries deep cycle batteries?

IFe04 rechargeable batteries are the first choice for use in deep cycle operations. It weighs about the halite of a lead-acid batter, but has a lifespan 3-5 times longer. In most cases, the lifep04 battery can be discharged to 80% or more without affecting the battery’s cycle life. The charging speed can also be increased 2-3 times as it can handle higher charging currents. Each LiFeP04 battery from WANROY has an internal battery management system. This provides many security and high performance features

No.se are safer than Ble Sure AG batteries. In addition, WANROY batteries have built-in protection. These protect against short circuits and have under/over voltage protection unlike lead acid/AG batteries which contain sulfuric acid which could leak and harm the environment and your equipment. Lithium batteries, on the other hand, are sealed, there is no liquid inside and no gas leaks out.

A WANROY LiFeP04 battery can be used for 3000-500 operating cycles, after 10 years or more of use Ble-Sure and AGM batteries can reach about 300-500 operating cycles before their capacity decreases significantly, although a WANROY battery in the Vorteld costs more you save a lot of money in the course of time,

Keep battery temperature below 45’C (below 30C if possible) — This point is by far the most important! Keep charging and discharging currents below 0.5C (preferably 0.2C). Keep battery temperature while discharging above 0°C if possible. Do not discharge the battery below 10% – 15% SOC unless you really have to. Avoid keeping the battery at 100% SOC if possible. Do not charge the battery to 100% SOC , unless this is necessary

Recommended storage temperature: -5 to +35C (23 to 95°F)Up to 1 month storage time: -20 to +60C (4 to 140°F)Up to 3 months storage time: -10 to +35°C (14 to 95F )long-term storage: +15 to +35*C (59 to 95°F)

This is not required. To fully charge a 12V LiFep04 battery, a charger with a voltage of 14V to 146V is required. Most AGB battery chargers are in this range and compatible with WANROY battery. If you use a lower voltage charger, it can charge the battery but not 100%. If you charge with a higher voltage, the battery will not charge and the BMs will go into protection mode and its high voltage shutdown function.

A liFePO4 battery is best charged with a liFep04 charger, as this is equipped with the correct voltage limit. Lead-acid battery chargers, on the other hand, often have voltage limits that are too high, which can lead to the battery management system (BMS) going into protection mode and error codes appearing on the charger display.

When charging a lithium iron phosphate battery, an external voltage is applied to increase the battery’s cathode current. The ideal way to charge a lithium iron phosphate battery is to use a lithium iron phosphate charger to set the correct voltage limit. If a lifep04 battery is not fully discharged, it does not need to be recharged after each use.life04 -Baters are not damaged even when teloe is loaded. When the liFeP04 battery is 80% discharged, you can recharge it. If the battery management system (BMS) switches off the battery due to undervoltage, the corresponding load is removed immediately and the battery is charged. Here you can find out what you need to know about charging. Check the battery charger before you use the charging device or is damaged.Charging board terminals should be clean and mismatched with battery posts to ensure good connection and optimal conductivity.Charging conditionsLithium iron phosphate batteries can be safely charged between 0C and 45C 32 and 113F.Lithium iron phosphate battery Batteries do not need any additional temperature compensation in terms of voltage when charging under high or low temperatures.When the BMs disconnects above and below the temperature, the battery needs to be warmed up to prevent the BMs from connecting and accepting the charging current, while the BMS shuts down due to high temperatures , the battery needs to be cooled

la, alternators are capable of charging lifep04 ateria. Unlike lead-acid batteries, however, the internal resistance of liFep04 batteries is very low. If the charging current is too high, the generator will overheat, smoke or even catch fire. You must therefore install a DC converter to limit the current the life0 batere also reaches the charge protection voltage, the BMS shuts down the circuit, creating a high spamnunas spike. This is also bad for the battery.

series charge If you connect batteries in series, make sure that the voltage between the individual batteries is less than 50 my (05 V). This minimizes the risk of voltage imbalance between cells. Parallel loading: Make sure the voltage between each cell is less than 0.1V to avoid cell-to-cell imbalance. When charging a 12–LiFePO4 battery, the charging voltage should be between 14V and 14.2V. If the battery cells are not balanced, you should charge each cell individually to bring them back into balance. In addition, you can regularly charge each battery individually to avoid imbalances. If you want to learn more about parallelization, please read this article

Overcharging lithium iron phosphate batteries can permanently damage them. Ctop means that the battery is charged well beyond its full charge voltage becomes. Overcharging can occur for the following reasons Lack of a proper battery protection system Persistent failure of the battery protection system Incorrectly installed battery protection system On the other hand, excessive discharge can also lead to battery damage. As soon as a battery is almost empty, the BMS should stop chargingIf you want to learn more about the LiFePO4 battery test. Please read this article

la.While charging is in progress, the output voltage of the charging device remains constant. If the charging status of the batere changes, the charging current is automatically adjusted. If the specified value for the voltage constant is correct, the battery can be fully charged.

Another advantage of liFeP04-Bears best carn. that the Entacunosrate has hardly any impact on the lercapaztat nat You can be continuously discharged at 100% DOD, ne that this has annotristoe effects, However, we recommend only discharging up to 80% in order to preserve the battery life.

The main functions of a BMS are to improve battery utilization, prevent battery overcharge and overdischarge, extend battery life, and monitor battery status. overload protection 2. Charge monitoring and control 3.Deep discharge protection 4. Cell temperature protection 5.Surge protection 6.BMS temperature protection 7. Active Cell Balancing 8.Short circuit security

To do this, you should first know how to charge a lithium battery and how we can request charging of such a battery. With the Kautener lithium battery you can have a leichmabioe power supply. more charging time and faster charging than other batteries. It is recommended to choose a charger that is compatible with the battery type in question. The charging time can be calculated by dividing by the amps of the charger. A 100 amp hour liFePO4 battery takes 2 hours to charge with a 50 amp charger. The charging time may depend on the charge rate used for the lithium battery. A 500 Ah battery takes about 5 hours to charge with a 100 amp charger. If this charge capacity is exceeded, the battery life can be damaged and its cycle time shortened. For more information on charging LiFePO4 batteries, please contact support@wanroy.de

Yes, LiFePO4 batteries can be used in cars.

Q: Can I use the WANROY Portable Power Station to charge my devices? Like HS600.

First, check the device’s performance, measured in watts. If it is less than the output power of your portable power station’s AC port, it can be supported by the portable power station.
For example, the WANROY Kraftwerk HS600 can operate AC units with 230 V that require less than 500 W.
Then you can calculate the charging time using the following formula: Operating time = HS600 Watt hours *0.85 / operating power of your device.
Example:
Suppose the power consumption of your device is 60W (e.g. a case fan) and you want to use the HS600 to power your device. 648Wh*0.85/60W = about 9 hours of operation time. Please note. that the actual power consumption depends on many factorsIf you want to learn more about charging portable power stations. Please watch this video:

WANRO power stations can be charged with a solar module from a third-party supplier. The size of the plug and the Finoanossamruno. with which you want to charge must match the WANROY station. We cannot recommend any other branded products to charge your WANROY power station. We cannot guarantee the safety and quality of bad products, nor can we provide after-sales service for these products. It is highly recommended that you purchase the appropriate WANROY solar panel(s) for your WANROY HS600. If you want to learn more about the portable power station review. Please watch this video:

Yes, however, the charging efficiency is low, resulting in a longer charging time.

That’s not true, you had to use the same parameters of solar cells to charge the power station. The voltage of 28W solar panel is 4Y and the voltage of 60W solar panel is 18V. Mixing the two will cause the high voltage back to the low voltage, damaging the circuit and damaging the power station. If you want to learn more about WANROY solar panels, please watch this video.

We recommend. keep battery power above 20%. when you use or store the Powerstation recelmaRig Please leave the product at room temperature and avoid a humid environment. To increase battery life, please charge the battery pack to the fifth level if the device is not used for more than 3 months.

On the product page you will find the ‘Specifications’ tabs where you can find most information about each product.

Unfortunately, you can’t. FAA regulations do not allow you to take a battery larger than 100Wh on an airplane

Each WANROY power station is made from a high-quality ternary lithium battery.
We choose only reliable battery suppliers.

Please contact us via support@wanroy.de, we will be happy to help you and offer you a solution within 24 hours on weekdays

Yes, there is a regulator in the battery.